User:Matt Hartings/Notebook/AU Biomaterials Design Lab/2013/09/18

Error creating thumbnail: Unable to save thumbnail to destination Biomaterials Design Lab

Main project page Previous entry      Next entry

Objective We're going to perform a redox titration on HRP in order to determine the standard potential of this protein. Description We will use a Pine Instruments Honeycomb Spectroelectrochemical cell coupled to a WaveNow USB Potentiostat. The redox reaction will be monitored using a galvanic cell setting. UV Vis spectra will be recorded on an Ocean Optics Jaz Spectrometer. We will specifically use the Q-band to observe redox state following with my results from yesterday. Following the procedure in this reference, we will add DTT in 1uL increments and observe both the UVVis spectrum and the open circuit potential of the SpecEchem cell. We will ultimately plot %oxidized or %reduced versus voltage read. The degassed buffer will contain: 50mM Tris 50mM NaCl and the following redox mediators (in order to stabilize the solution potential) 20uM duroquinone (tetramethyl-1,4-benzoquinone) (for 20mM should measure 32.8mg in 10mL) 10uM pyocyanine (we didn't receive this chemical) 10uM 2-hydroxy-1,4-naphthoquinone (for 10mM should measure 17.415mg in 10mL) 10uM anthraquinone-2-sulfonate (for 10mM should measure 31.026mg in 10mL) 2uM benzyl viologen (1,1'-Dibenzyl-4,4'bipyridinium Dichloride Hydrate) (for 2mM should measure 8.187mg) 1uM phenylsafranine (for 1mM should measure 3.228mg) 1uM indigo-carmine (for 1mM should measure 4.66mg) Our HRP concentration will be roughly 30uM (in order to better observe the Q-bands). Also, the cuvette path length is shorter than 1cm, so we'll need a higher concentration to observe spectral changes. The final concentration of DTT should be 2000X the HRP concentration. This comes out to 60mM. We should perform 1uL additions. The initial volume in the cuvette will be 1.1mL (1mL is initially added to the cuvette and 0.1mL used to fill the honeycomb). (the sodium dithionite stock solution should be ~10M unfortunately the max solubility is 1.4M). Data The buffer that was made yesterday will be used today with more degassing. Sodium Dithionite 6.3419g in 25.0mL --> 1.46M Degassed for 2 hours Dyes All of the dyes were placed in the same 10mL volumetric Duroquinone: 33.3mg in 10mL --> 20.3mM 2-hydroxy-1,4-naphthoquinone 18.0mg in 10mL --> 10.3mM anthraquinone-2-sulfonate 30.8mg --> 9.93mM benzyl viologen 8.7mg --> 2.1mM phenylsafranine 2.6mg --> 0.81mM indigo-carmine 4.6mg --> 0.99mM These dyes were diluted by a factor of 1000 (25uL into 25mL). This solution was then degassed for 1 hour. Error creating thumbnail: Unable to save thumbnail to destination The dye solution has a blue-ish tint to it. HRP Measured 13.2mg in 10mL (dye solution) --> 33uM Notes This area is for any observations or conclusions that you would like to note. Use categories like tags. Change the "Course" category to the one corresponding to your course. The "Miscellaneous" tag can be used for particular experiments, as instructed by your professor. Please be sure to change or delete this tag as required so that the categories remain well organized.