Difference between revisions of "User:Ellen Petersen/Notebook/MOF/2013/06/26"

From OpenWetWare
< User:Ellen Petersen‎ | Notebook‎ | MOF‎ | 2013‎ | 06
Jump to: navigation, search
(DPNI: 06-26-13)
(2 intermediate revisions by the same user not shown)
Line 19: Line 19:
 
* 10.) Solution stable at 135 degrees at 35, mark red line on it to see difference in solution level.  
 
* 10.) Solution stable at 135 degrees at 35, mark red line on it to see difference in solution level.  
 
______________________________________________________________________________________________________
 
______________________________________________________________________________________________________
 +
 +
06-27-13
 +
 +
* 11.) Turn off nitrogen and water, Cool to Room Temperature
 +
* 12.) Not enough diethyl ether, took 400 mL of diethyl ether (instead of the required 600 mL) and poured 2/3's of DPNI solution into the 400 mL of diethyl ether.
 +
* 13.) Filter out
 +
 +
______________________________________________________________________________________________________
 +
 +
07-02-13
 +
 +
*14.) Ran 1/4 of the DPNI with 150 mL of ethanol through the rotavap
 +
 +
______________________________________________________________________________________________________
 +
 +
07-05-13
 +
 +
*15.) Ran the rest of the DPNI with 150 mL of ethanol through the rotavap
 +
  
  

Revision as of 11:59, 8 July 2013

Owwnotebook icon.png MOF <html><img src="/images/9/94/Report.png" border="0" /></html> Main project page
<html><img src="/images/c/c3/Resultset_previous.png" border="0" /></html>Previous entry<html>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;</html>Next entry<html><img src="/images/5/5c/Resultset_next.png" border="0" /></html>

DPNI: 06-26-13

  • 1.) Add solids 1,4,5,8 Naphthalenetetracarboxylic dianhydride (.805 g, 3.00 mmol) and 4-aminopyridine (.847 g, 6.00 mmol)to round bottom flask (I added .8054 g of 1,4,5,8 Naphthalenetetracarboxylic dianhydride, and .8479 g of 4-aminopyridine)
  • 2.) Add 150 mL of solvent (DMA) ~keep under hood~
  • 3.) Add Stir Bar to solution
  • 4.) Put under spout and raise black knob until there is enough pressure to hold it in place
  • 5.) Begin to stir
  • 6.) If attached to condenser, turn on water very slightly
  • 7.) Turn on nitrogen: ensure bubbles are about 1 every 4 seconds. (Turn little end of nossle up)
  • 8.) Turn on heat to 50, switch down accordingly until it reaches 135 degrees consistently.
  • 9.) If solution seems to be boiling adjust and turn down
  • 10.) Solution stable at 135 degrees at 35, mark red line on it to see difference in solution level.

______________________________________________________________________________________________________

06-27-13

  • 11.) Turn off nitrogen and water, Cool to Room Temperature
  • 12.) Not enough diethyl ether, took 400 mL of diethyl ether (instead of the required 600 mL) and poured 2/3's of DPNI solution into the 400 mL of diethyl ether.
  • 13.) Filter out

______________________________________________________________________________________________________

07-02-13

  • 14.) Ran 1/4 of the DPNI with 150 mL of ethanol through the rotavap

______________________________________________________________________________________________________

07-05-13

  • 15.) Ran the rest of the DPNI with 150 mL of ethanol through the rotavap