Difference between revisions of "Smolke:Protocols/Yeast Colony PCR"

From OpenWetWare
Jump to: navigation, search
m (Procedure)
m (Genomic Prep by Harju Bust'n'Grab)
Line 38: Line 38:
==Genomic Prep by Harju Bust'n'Grab==
==Genomic Prep by Harju Bust'n'Grab==
*overnight yeast cultures
*lysis buffer - 2% Triton X-100, 1% SDS, 100 mM NaCl, 10 mM Tris-HCl (pH 8.0), 1 mM EDTA (pH 8.0)
*ethanol (70% and 100%)
*sodium acetate
Line 58: Line 64:
#Wash pellet with 70% ethanol
#Wash pellet with 70% ethanol
#Re-suspend in 50 µl TE  - use 1 µl in a PCR reaction
#Re-suspend in 50 µl TE  - use 1 µl in a PCR reaction
Note: Lysis buffer contains 2% Triton X-100, 1% SDS, 100 mM NaCl, 10 mM Tris-HCl (pH 8.0), 1 mM EDTA (pH 8.0)
==Genomic Prep by Phenol:Chloroform with Glass Beads==
==Genomic Prep by Phenol:Chloroform with Glass Beads==

Revision as of 21:57, 26 October 2011

Smolke top.gif

Home        Contact        Internal        Protocols        Lab Members        Publications        Research       


Colony PCR from yeast, either to check inserts etc. or for sequencing.

Travis' Version (Lyticase lysis)


  • Lyticase (from Sigma)
  • TE
  • PCR buffers, primers, polymerase, etc.


The basic idea is breaking the cells with lyticase and heat, then doing PCR.

  1. Dilute stock of lyticase to 50 U/mL in TE.
  2. Aliquot lyticase in 50uL quantities
  3. Pick colonies (I use a pipette tip) and add to lyticase aliquots, pipette up and down or agitate to break up colony
  4. Incubate at 37°C for 30 min
  5. Incubate at 95°C for 10 min
  6. Use as template for PCR - I use 5uL of the cells in a 50uL PCR reaction


  • I use this protocol to PCR off the chromosome for sequencing... I clean up the rxn with a Zymoclean kit afterwards.
  • The amount of yeast doesn't seem to matter much. I get success with very small colonies or with loads of cells.

Josh's Version (NaOH lysis)


  • 20 mM NaOH
  • PCR materials


  1. Aliquot 20uL NaOH into PCR tubes
  2. Pick colonies (I use pipet tips) into the NaOH
  3. Incubate at 95C for ~45 minutes
  4. Centrifuge at max speed for 10 minutes (helps to use plastic inserts in the microfuge)
  5. Use 1uL of supernatant as template in a (10uL) PCR.

Genomic Prep by Harju Bust'n'Grab


  • overnight yeast cultures
  • lysis buffer - 2% Triton X-100, 1% SDS, 100 mM NaCl, 10 mM Tris-HCl (pH 8.0), 1 mM EDTA (pH 8.0)
  • phenol:chloroform
  • chloroform
  • ethanol (70% and 100%)
  • sodium acetate
  • TE


Adapted by Kate from Harju et al., 2004

  1. Spin down 1.5 ml O/N culture and remove media
  2. Re-suspend in 200 µl lysis buffer and transfer to a thin-walled PCR tube
  3. Freeze at -80 °C, 5 min
  4. Thaw at 95 °C, 1 min on PCR block
  5. Repeat once and transfer to 1.5 mL eppendorf tube
  6. Vortex vigorously
  7. Add 200 µl phenol:chloroform and vortex well
  8. Spin 2 min, remove aqueous phase
  9. Add 200 µl chloroform and vortex well
  10. Spin 2 min, remove aqueous phase
  11. Add 400 µl ice-cold ethanol and 40 µl sodium acetate
  12. Precipitate at -80 °C, 5 min
  13. Spin 5 min at 4 °C
  14. Wash pellet with 70% ethanol
  15. Re-suspend in 50 µl TE - use 1 µl in a PCR reaction

Genomic Prep by Phenol:Chloroform with Glass Beads



Adapted by Mike from protocol from friend in the Herschlag group, and further adapted by Stephanie

  1. Grow 3-10 ml culture of yeast to saturation. (You can even use this protocol on single colonies if you don't need much DNA.)
  2. Collect cells by centrifugation in 1.5 ml eppendorf tube (max speed, 15 s).
  3. Aspirate supernatant and resuspend in 500 µl of ddH2O. Pellet, decant.
  4. Pipette briefly to resuspend pellet in residual liquid.
  5. Add 200 ul detergent lysis buffer, ~100 mg (50uL) glass beads.
  6. Tape to vortex machine in cold room, vortex for 10-20 min. (You can vortex for 2 min at room temp if you don't need much DNA.)
  7. Add 200 ul PCI (phenol:chloroform:isoamyl alcohol:TE; 25:24:1), vortex briefly.
  8. Centrifuge at max for 5 min (4 °C).
  9. Transfer aqueous top layer to fresh eppendorf tube.
  10. Add 50 ul 3M sodium acetate, then 1 ml ice cold 100% EtOH.
  11. Spin for 10-20 min at high speed at 4 °C.
  12. Decant off liquid and vacufuge until pellet dries.
  13. Resuspend in ~100 uL water, 1x TE buffer pH 8.0, or EB buffer.
  14. For PCR use 1 ul of 1:10 or 1:100 dilution of the resuspension as template - this varies depending on the strain, shearing, and how well your genomic isolation went. You can nanodrop the resuspension to estimate the concentration, and use 10-30 ng in a 25 uL PCR reaction.

Note: Detergent lysis buffer is 2% Triton X-100, 1% SDS, 100 mM NaCl, 10 mM Tris pH 8.0, 10 mM EDTA.