Sauer:ClpA purification
ClpA Purifcation Protocol
Jon Kenniston / Julia Flynn / John Lo
General Notes
- Do all purification steps at 4°C.
- Thoroughly wash columns before use.
- All buffers should be filtered, degassed, and stored at 4oC.
- Run fractions on 8% polyacrylamide gels (ClpA = 84 kD)
- ClpA pI = 5.868 (Colibri), 6.3 (Maurizi)
Procedure
1. Grow O/N in 3 mL LB/Kan ClpA frozen stock (M169T in pET-9a, BL21(DE3)).
2. Inoculate 1 L LB/Kan each culture – 4 L total.
3. Grown until A600 1.0, then induce with 0.4 mM IPTG for 2 hours.
4. Spin at 4000 rpm for 20 minutes.
5. Resuspend pellets in 5 mL Lysis Buffer. Try adding salt to lysis buffer? 100 mM KCl sounds good here.
6. Freeze overnight in -80oC.
7. Thaw cells with additional 25 mL Lysis Buffer + Calbiochem protease inhibitor cocktail.
8. French Press 2X. (or sonicate, 5x 30s)
9. Spin at 19,000 rpm for 1 hour in Sorvall. Remove and keep supernatant.
10. Add 40 mL 100% saturated AmSO4 to the supernatant (~60 mL) for final concentration of 40%. Incubate at 4oC for 1 hour. (or overnight)
11. Spin at 12,000 rpm (20k x g) for 30 min. and resuspend pellets in 40 mL of S-column Buffer A (~6.25 mL/g).
12. Spin cloudy resuspension another 30 minutes at 12,000 rpm. Keep supernatant.
13. Check conductivity. Ensure that sample has less conductivity than S-column Buffer A alone. If needed, dilute or dialyze sample with S-Sepharose buffer without KCl, or add KCl if greatly under-conductive. (always overconductive. Dilute with S-Sepharose Buffer A, no salt)
14. Run sample over S-Sepharose column (<50 mL) and elute with gradient of 0.2 M – 1 M KCl in Buffer B at 0.5-0.75 mL/min.
15. Check fractions on SDS-PAGE and compare with original over-expression sample.
16. Combine fractions and add AmSO4 to be 0.6 M (~15%).
17. Equilibrate Phenyl-Sepharose column (10-20 mL) with Phenyl-Sepharose Buffer A with 0.6% CHAPS.
18. Load sample onto column.
19. Gradient Buffer A to Buffer B at 2 mL/min for 60 minutes
20. Pool peak fractions and concentrate using Amicon tubes 5,000 rpm.
21. Dialyze against 4 L HO buffer overnight. Change 2 to 3 times.
22. Make 100 µL and 50 µL aliquots, and store at -80oC.
Buffers
Lysis Buffer:
- 50 mM Tris-Cl, pH 7.5
- 2 mM DTT
- 2 mM EDTA
- 10% glycerol
S-Sepharose Buffer A:
25 mM HEPES, pH 7.5 200 mM KCl 2 mM DTT 0.1 mM EDTA 10% glycerol
S-Sepharose Buffer B:
- 25 mM HEPES, pH 7.5
- 1.0 M KCl
- 2 mM DTT
- 0.1 mM EDTA
- 10% glycerol
Phenyl-Sepharose Buffer A:
- 50 mM NaPO4, pH 7.5
- 2 mM DTT
- 10% glycerol
- 0.6 M (NH4)2SO4
Phenyl-Sepharose Buffer B:
- 50 mM NaPO4, pH 7.5
- 2 mM DTT
- 10% glycerol
- 0.6% CHAPS
Dialysis (HO) Buffer:
- 50 mM Tris-Cl, pH 7.5
- 100 mM KCl
- 1 mM EDTA
- 10% glycerol
- 2 mM DTT
4x ClpA Activity Buffer
- 200 mM HEPES pH 7.5
- 80 mM MgCl2 6H20
- 1.2 M NaCl
- 40% glycerol
- 2 mM DTT
