Difference between revisions of "Gill:Back Door"
|Line 17:||Line 17:|
up the spill the .
Revision as of 11:24, 22 November 2013
Disposing of Waste
Solid biohazardous waste should be sterilized in the kill autoclaves in the Biochemistry Building at 121 °C for an hour. Close the plastic waste bag, leaving a small opening at the top so that steam can enter and escape. Place the bag in an autoclave-safe tray, and place heat-sensitive tape over the biohazard symbol. After autoclaving, allow the bag to cool, place it in a black garbage bag, and then dispose of it in the dumpster.
To dispose of BL-1 liquid biohazardous waste, add 10% bleach to the container, let it sit for a minimum of 20 minutes, and then pour it down the drain. BL-2 liquid biohazardous waste should be sterilized in a kill autoclave for an hour before being poured down the drain. After sterilization, dispose of glass culture tubes in the broken glass box and save the caps.
Hazardous Chemical Waste
Leave the container in the fume hood until it is ready for pickup (i.e. until a large container is full, or a few smaller containers have accumulated). When ready for pickup, fill out a hazardous waste disposal tag (located in the drawer next to the fume hood). Attach the top portion of the tag to the container with twine and mail the lower portion to the Safety & Health Office (MS 4472).
Neutralize acid spills before cleaning up (acid neutralizing powder is in the spill kit under the sink).
To clean up a biohazardous spill...
- Remove any clothing and wash any body parts that came into contact with biohazardous material
- If biohazardous material is in your eyes, use the nearest eyewash station
- Alert others to the existence of the spill and/or mark the area
- Put on a lab coat, gloves, and safety glasses
- Cover the spill with paper towels
- Pour undiluted bleach over the area and allow it to soak for one hour
- Inform the PI about the spill
- If there is broken glass, use a broom and dustpan, forceps, or two pieces of cardboard to pick up the glass and dispose of it in a red biohazard sharps container
- Dispose of paper towels in an autoclave bag
- Wipe the area again with disinfectant
- Soak contaminated clothing or shoes in a tray with disinfectant
- Use autoclave gloves when loading/unloading the autoclave. A face shield can also be used.
- Fill containers to under 75% capacity.
- Loosen all caps before autoclaving, and tape them on one side.
- Make sure the pressure is at zero before opening the autoclave.
- Do not change the temperature on the autoclaves in the Biochemistry Building.
Autoclave for 30 minutes using the liquid cycle. After autoclaving, crack the door to release steam and then slowly open the door. To prevent explosion of superheated liquids, allow liquids to cool slightly before removing the tray.
Autoclave for 30 minutes using the gravity cycle, and leave in the dryer overnight.
Do Not Autoclave...
- Hazardous chemical waste such as bleach, ethidium bromide, HCl, and chloroform.
- Non-heat-resistant plastics such as polystyrene and polyethylene.
- Radioactive waste.
The pH Meter
- Rinse the pH probe with water before use.
- If necessary, calibrate the pH meter according to the instructions posted on the wall. At least check the calibration using the pH 7 buffer solution.
- Slide the tubing near the top of the pH probe up or down to open the vent, and close again when finished.
- If the vent gets covered with gunk, wipe it off with a paper towel, don't rinse with water.
- Don't let the filling solution get below the coil. If it completely dries out, rinse the probe with water before refilling.
- When taking measurements, make sure that the bulb and junction of the probe are submerged. Make sure that the stir bar does not break the bulb.
- When finished, rinse with water and put the probe back in the storage solution.