Biomod/2011/Caltech/DeoxyriboNucleicAwesome/SPEX Results

From OpenWetWare
Revision as of 22:30, 2 November 2011 by Zibo Chen (talk | contribs) (Mathematical Formulae)
Jump to: navigation, search


Saturday, October 21, 2017








SPEX Results

As discussed in SPEX Experimental Design, two sets of experiments were conducted to verify the random walking mechanism. The first set was performed to detect potential leak reactions in the system, while the second set of experiments were used to verify the random walking mechanism.

Detection of Potential Leak Reactions

To verify that the walker walks on the origami using the intended mechanisms, we set up control groups where either tracks (TR), except for the one that the walker is bound to, or walker triggers (WT), or both, were missing in the reactions. Walkers are not expected to perform random walking under such conditions. As shown in Figure 1, no decrease in fluorescent signals were observed unless both tracks and walker triggers were added into the system. Hence potential leak reactions are negligible.

Figure 1. Detection of Potential Leak Reactions. No decrease in fluorescent signals were observed unless both tracks and walker triggers were added into the reaction system. Different fluorescent levels could be attributed to pipetting errors. The gradual increase in fluorescent signals in three control groups was due to increase in fluorophore concentration caused by the evaporation of buffer.

Random Walking with Different Starting Positions

Figure 1. Unnormalized SPEX results for different lengths of tracks and space walking. Excess of walker triggers were added at 4000s to activate all the walkers. Excess of walkers tagged with quenchers were added at the end to terminate all the reactions.

Figure 1 shows the original unnormalized SPEX data. The walkers reached their destinations faster on shorter tracks.But this is not enough to show that the walkers were randomly walking on the surface of origami, because there was 5-fold excess of tracks in solution that the walker can strand displace onto from origami. We refer to this hypothetical process as 'space walking'. To test for this we designed a playground without any probes except for the one on the starting position of the walker (SP10) and that of the walker goal,but with 5-fold excess of tracks in solution, and we compared this to results of the walker on the regular playground at different starting positions.

As can be seen from the graph, space walking was the slowest process. As the rate of SW depends on the concentration of free floating tracks as well as the concentration of origami, the effect of SW on the overall rate of fluorophore quenching can be reduced by diluting free floating tracks and origami (data not shown). It was shown that the random walks all went to around 50% completion instead of 100%. This phenomenon could be attributed to malformed origami, misplanted tracks on the origami, or failure in planting walkers/walker goals.

This graph was normalized so the point at which the walker trigger was released starts at 1, and the point at where the fluorophores are assumed to be fully quenched is 0 (Figure 2). A similar trend was obtained: the rate of quenching was higher when the distance between starting point and walker goal was decreased. This is characteristic of a two dimensional random walk, but could not be used to confirm random walk, as a random walk is defined to be unbiased. Hence Matlab simulation and a mathematical model were employed to verify the occurrence of random walking on the origami.

Figure 2. Normalized fluorescent data. The point at which the walker trigger was released starts at 1, and the point where the fluorophores are assumed to be fully quenched is 0.

Data Analysis

Matlab Simulation

We used a stochastic MATLAB simulation to estimate half-completion times for walkers starting on truncated tracks of varying lengths:

Start Site, Truncated Track Effective Track Length in Columns Half-Completion Time in Branch Migration Steps
SP4 15 621
SP10 13 463
SP16 11 338
SP22 9 208
SP57 7 117
SP34 5 59

This data, along with the completion time formula generated via mathematical analysis of the track, can serve as controls for the random walk SPEX data.

Mathematical Formulae

We plotted the theoretical percentage of walkers that are still walking on the origami as a function of the number of steps; it mimics the decrease in fluorescent signals and is the expected normalized fluorescent signal graph.

Figure 1. A plot of the percentage of walkers that are still walking on the origami versus number of steps taken.

Normalized SPEX data for three different lengths of tracks was fitted to their respective random walk formula (Figure 2-4) by varying the time taken from one column to the adjacent one. It was found that experimental data can fit well with the theoretical curves within the range of fluorescent noises. Since the model proposed an unbiased random walk with equal forward and backward movement, it is highly likely that DNA walkers can walk on the origami in a truly random manner.

Figure 2. SPEX data fitting for random walking on the longest track (SP10).
Figure 3. SPEX data fitting for random walking on the medium length track (SP22).
Figure 4. SPEX data fitting for random walking on the shortest track (SP34).

Furthermore, the rate of random walk (time per step) was estimated using the half completion time in each situation. It was found that walkers needed 10 seconds to take one branch migration on the origami with longest track, 16 seconds on origami with medium length track and 27 seconds on origami with shortest track. However, the rate of branch migration should be the same regardless of the length of tracks. We are in the progress of collecting more data for further analysis. Taking the average of these three values ,the rate of branch migration in our case is calculated to be 18 seconds per branch migration, or 0.3 nm/s. This fits with the reported average speed, which was of the order of 0.1 nm/s [1].



[1] Wickham, S. F. J., Endo, M., Katsuda, Y., Hidaka, K., Bath, J., Sugiyama, H., & Tuberfield, A. J. (2010). Direct observation of stepwise movement of a synthetic molecular transporter. Nature Nanotechnology, 6, 166–169.