User:Moira M. Esson/Notebook/CHEM-581/2012/11/16

(Difference between revisions)

Revision as of 19:24, 26 November 2012

Project name

Standardize sodium bicarbonate solution
Run UV-vis on porphyrin films
Test swelling on all crosslinked glutaraldehyde films
Test the time necessary to facilitate a color change in various porphyrin using Fe₂(SO₄)₃ solution, Al₂(SO₄)₃ solution and Na₂SO₄.
Run UV-vis on color changed porphyrin films

General protocol for UV-vis on porphyrin films:

Remove crosslinked porphyrin films from deionized H₂O and pat dry using a paper towel
Using a quartz cuvette as a guide, cut a strip of paper the same width as the quartz cuvette.
Using the strip of paper as a guide and scissors(or a similar sharp instrument) carefully cut the porphyrin film the same width as the paper reference. When cutting the film, try and use a smooth portion of film.
Measure the thickness of the film. This will be used as the pathlength.
Using forceps, carefully place the cut strip of film in a clean quartz cuvette.
Using a spatula, gently press the film against the cuvette.
Carefully place the cuvette into the Shimadzu 2550 spectrophotometer.
Measure following the general protocol for UV-vis measurements

Porphyrin film UV-vis pathlengths:

Film measured	Thickness of film(mm)
2.4394g PVOH(22K)+0.5mLGA+0.99mL porphyrin prepared 10/19	0.77
PVOH(22K) 1.0073+1.0mL GA+1mL porphyrin prepared 10/24	0.79
PVOH(22K) 1.02114g+0.5mL GA+1mL porphyrin prepared 10/26	1.01
PVOH(22K) 1.0067g+1mL GA+1mL porphyrin	1.27
PVOH(22K) 1.05225g+ 0.5mL GA+1mL porphyrin prepared 10/24	0.8

New weights of PHP used:

Titration information:

The general protocol for titrations was used. The sodium bicarbonate solution prepared2012/11/09 was used as the base. Three drops of bromothymol blue was added each PHP solution.

General Protocol for film swelling:

Cut small piece of crosslinked glutaraldehyde films and place in small beaker. Allow to completely dry for ~48 hours
Weigh small piece of film. Record mass.
Place dry piece of film in 10mL beaker and add 10mL HPLC grade H₂O to completely cover the film. Parafilm the beaker and allow to sit for three days.
Reweigh the film. Record the mass.

Please refer to Melissa Novy's lab notebook for swelling information.

Note: Small pieces of film used for FTIR measurement were used for swelling information.

@@ Line 70: / Line 70: @@
 #Cut small piece of crosslinked glutaraldehyde films and place in small beaker. Allow to completely dry for ~48 hours
 #Weigh small piece of film. Record mass.
-#Place dry piece of film in 10mL beaker and add enough deionized H<sub>2</sub>O to completely cover the film. Parafilm the beaker and allow to sit for ~48 hours.
+#Place dry piece of film in 10mL beaker and add 10mL HPLC grade H<sub>2</sub>O to completely cover the film. Parafilm the beaker and allow to sit for three days.
 #Reweigh the film. Record the mass.
 <br>
 Please refer to [[User:Melissa_Novy/Notebook/CHEM-581/2012/11/16|Melissa Novy's lab notebook]] for swelling information.
 *Note: Small pieces of film used for FTIR measurement were used for swelling information.
 ==Color Change of porphyrin films==