User:Megan L. Channell/Notebook/Masters Research/2013/10/24

From OpenWetWare

< User:Megan L. Channell | Notebook | Masters Research | 2013 | 10(Difference between revisions)
Jump to: navigation, search
(Autocreate 2013/10/24 Entry for User:Megan_L._Channell/Notebook/Masters_Research)
Current revision (16:24, 5 November 2013) (view source)
(Protocol)
 
(2 intermediate revisions not shown.)
Line 6: Line 6:
| colspan="2"|
| colspan="2"|
<!-- ##### DO NOT edit above this line unless you know what you are doing. ##### -->
<!-- ##### DO NOT edit above this line unless you know what you are doing. ##### -->
-
==Entry title==
+
==PLA Film==
-
* Insert content here...
+
* Make Polylactic acid (PLA) film with MOF-5 that was made [[User:Megan L. Channell/Notebook/Masters Research/2013/10/3|here]].
 +
==Protocol==
 +
#0.1 %, 0.5 %, 1.0 %, 5.0 %, 10 % and 0 % w/v.
 +
##0.1 % - 0.9993 g PLA, 0.0013 g MOF-5, 10 mL dichloromethane
 +
##0.5 % - 0.9951 g PLA, 0.0052 g MOF-5, 10 mL dichloromethane
 +
##1.0 % - 0.9904 g PLA, 0.0099 g MOF-5, 10 mL dichloromethane
 +
##5.0 % - 0.9497 g PLA, 0.0495 g MOF-5, 10 mL dichloromethane
 +
##10.0 % - 0.9000 g PLA, 0.9899 g MOF-5, 10 mL dichloromethane 
 +
##0 % - 0.999 g PLA, 10 mL dichloromethane
 +
#Used the ultrasonic to mix each sample in a plastic vial until dissolved completely.
 +
#Once dissolved, poured into molds to set.
 +
==Note==
 +
The 10% is not 10% because there was too much MOF-5.  This needs to be re-done.
<!-- ##### DO NOT edit below this line unless you know what you are doing. ##### -->
<!-- ##### DO NOT edit below this line unless you know what you are doing. ##### -->
|}
|}
__NOTOC__
__NOTOC__

Current revision

Project name Main project page
Previous entry      Next entry

PLA Film

  • Make Polylactic acid (PLA) film with MOF-5 that was made here.

Protocol

  1. 0.1 %, 0.5 %, 1.0 %, 5.0 %, 10 % and 0 % w/v.
    1. 0.1 % - 0.9993 g PLA, 0.0013 g MOF-5, 10 mL dichloromethane
    2. 0.5 % - 0.9951 g PLA, 0.0052 g MOF-5, 10 mL dichloromethane
    3. 1.0 % - 0.9904 g PLA, 0.0099 g MOF-5, 10 mL dichloromethane
    4. 5.0 % - 0.9497 g PLA, 0.0495 g MOF-5, 10 mL dichloromethane
    5. 10.0 % - 0.9000 g PLA, 0.9899 g MOF-5, 10 mL dichloromethane
    6. 0 % - 0.999 g PLA, 10 mL dichloromethane
  2. Used the ultrasonic to mix each sample in a plastic vial until dissolved completely.
  3. Once dissolved, poured into molds to set.

Note

The 10% is not 10% because there was too much MOF-5. This needs to be re-done.


Personal tools