Tasks for October 8
- [I-] by Titration Precipitation
- To set up a new dialysis experiment containing [I-]
[I-] by Titration Precipitation
Procedure followed as detailed by Dr. Fox
- Prepare 50 mL 50 mM KI Stock Solution (store in 50 mL Falcon tube)
- 0.415g of KI were added to 50 mL volumetric flask and distilled water was added to make up to mark
- Prepare 50 mL 75 mM AgNO3 Solution
- Be very precise with your measurements (use Rm 205 balance)
- 0.63701 g of AgNO3 were added to 50 mL volumetric flask and distilled water was added to make up to mark
- Store in Black 50 mL Falcon tube
- Prepare 100 mL 10 mM NH4SCN Stock Solution (store in Falcon tubes)
- 0.0761 g of NH4SCN were added to 100 mL volumetric flask and distilled water was added to make up to mark
- NH4SCN Standardization
- Add 3 mL 1 M HNO3 and 2 mL AgNO3 to 10 mL DI H2O
- Add 200 μL Ferric alum indicator
- Titrate with your NH4SCN solution
- Your solution should turn red around 15 mL. Volume required for first titration=15.5mL. Second titration=15.5mL'
- AgNO3+NH4SCN→AgSCN+NH4NO3
- Reaction is 1:1
- 2mL of AgNO3=1.5×10-4 mol
- 15.5 mL of NH4SCN contain 1.5×10-4mol
- [NH4SCN]=9.68 mM
- Concentration of AgNO3 at the lowest saturated concentration:
- [Ag][SCN]=Ksp where Ksp=1.03×10-12 (at 25ºC)
- x2=Ksp
- [Ag] at the lowest saturated concentration=1.01μM
- KI Standardization
- Add 3 mL 1 M HNO3 and 1 mL KI to 10 mL DI H2O
- Add 2 mL AgNO3 and swirl to complete precipitation
- Add 200 μL Ferric alum indicator
- Titrate with your NH4SCN solution
- Your solution should turn red around 10 mL. Volume required for titration in first titration=10.3mL. Second titration=10.5mL
- KI+AgNO3→AgI+AgNO3+KNO3
- AgNO3+NH4SCN→AgSCN+NH4NO3
- 10.3 mL of NH4SCN were required to titrate excess AgNO3. (=9.9704×10-5mol)
- 2mL AgNO3 contain 1.5×10-4 mol
- 1.5×10-4−9.9704×10-5=5.0296×10-5 mol of AgNO3 reacted with KI in a 1:1 reaction
- 1 mL of KI contains 5.0296×10-5 mol
- [KI]=50.296 mM
- [I-] for dialysis
- Follow the same procedure as your KI standardization
- Note that your limit of detection will be based on how small a volume you can read (0.1 mL = 1 mM LOD)
- You may want to try a new NH4SCN solution (more dilute) for smaller concentrations.
Fluorescence of protein solutions
- Measured fluorescence of dyalised solutions from Oct.1
- Fluorescence (glass microcuvette & 100 fold diluted) for all protein solutions
- 10μL of dialysed colloid or lysozyme were diluted to 1mL by adding distilled water. (Remember to account for dilution factor later on)
Preparation of new Dialysis with 0.6 g/ L Lysozyme vs KI using 3500 MWCO
- Add 1 mL Lysozyme to 5 wells on one side
- Make serial dilutions of KI at 50 mM, 25 mM, 10 mM, 5 mM, and 2 mM
- Add a different concentration to each well on the opposite side.
- Place on low speed shaker for 1 week
Dialysis Data
Bradford Analysis
|