SBB09Ntbk-Sadao Ota

Sadao 13:20, 22 April 2009 (EDT)

Summary of Activities:
*
*
To do today:
* Prepare Tris buffer solution
* Prepare AgNO3 solution
* Run assay

AG4 Silver biomineralization assay

Preparation of Tris buffer (1*) solution

adjust Ph 7.4 with adding 1M HCl

Preparation of AgNO3 solution

• Weigh AgNO3 powder in an Eppendorf tube (weighed 0.013 grams)
• AgNO3 has MW 169.87 g/mol - dilute 0.013g with 0.750ml for ~10 mM solution
• Make 3ml of 1mM solutions by adding 100ul of 10mM AgNO3 into 900ul of H2O

Sadao 5:04, 21 March 2009 (PST)

I was not in lab today, but Susan and Roger carried out the following work:

Summary of Activities:
* Grew one colony from each sample (11-17) and control in 4ml LB media (with CA)
* Grew one colony from each sample (11-17) and control in 4ml LB media and 0.1mM AgNO3 (with CA)
* [http://openwetware.org/wiki/Image:Silver_binding1.doc growing cells grid]

Sadao 13:41, 20 April 2009 (EDT)

The composite parts have been assembled, and now we are doing assays for the different constructs. I am doing the AG4 silver binding peptide assay (Construct 18) with Carlos, Roger, Sadao, and Susan.

Our assay protocol can be found here:

Silver biomineralization assay

Summary of Activities:
* Tested 1M, 100mM, 10mM, 1mM, 0.5mM, 0.1mM AgNO3 in LB media
* A precipitate formed with AgNO3 in LB all the way down to 0.5mM
* 0.1mM AgNO3 in LB media did not form a visible precipitate
* Transformed constructs into bacteria (Roger and Susan)
* Plated the cells (Roger and Susan)
* We will use constructs 11-17 and a pBca9145-Bca1363 as control
To do today:
* Test AgNO3 precipitation in LB Media

AG4 Silver biomineralization assay

Preparation of AgNO3 solutions

• Weigh AgNO3 powder in an Eppendorf tube (weighed 0.88 grams)
• AgNO3 has MW 169.87 g/mol - dilute 0.88g with 0.5ml for ~10 M solution
• Dilute it down to 10mM
• Create 1 mM, 0.1 mM, and 0.05 mM dilutions by adding 9+1, 9+1, and 1+1 parts of H2O and AgNO3 solution

Test AgNO3 precipitation in LB media

• Prepare Eppendorf tubes with 200ul of LB media
• Dilute 1M, 100mM, 10mM, 1mM, 0.5mM, and 0.1mM AgNO3 in LB media
• Mix and check for precipitate - if no precipitate, spin down in centrifuge and look for pellet

Sadao Ota 15:03, 9 February 2009 (EST)

My project is SBB09_20154, to make ag43 Display (short) ag43 Display (long) systems. Designed a oligo M10034 to make Autotransporter protein with promotors and so on (corresponding to amino acids 708-1017). Also, designed another oligo M10035 to make Autotransporter protein only (corresponding to amino acids 517-1017).

• Construction files are M10034 M10035
• Oligonucleotide sequences are Oso001, Oso002, Oso003

Sadao Ota 15:03, 16 February 2009 (EST)

Do PCR with the combination of Oso001&Oso002, and Oso002&Oso003.

PCR Cloning

Sadao Ota 15:03, 23 February 2009 (EST)

Clean up PCR products for gelation analysis

Clean up PCR products, Digest, Clean up and gel again.

Regular Zymo Cleanup (removes the polymerase, dNTPs, buffer, and most of the oligonucleotides from a PCR reaction) here

Load to Gel to perform gelation analysis (dead or alive) here

EcoRI/BamHI Digest of PCR Products (my PCR products are large enough, so no need to modificate the process) here

Sadao Ota 15:03, 25 February 2009 (EST)

Ligation of EcoRI/BamHI digests

I used gel to separate the DNA I need I also used digested DNA without gelation to do heat shock.

2nd PCR cloning did not work. So, PCRing again...