Maxiprep of plasmid DNA from E. coli

This protocol produces very clean, concentrated DNA, usually on the order of several mg/mL. It is labor intensive. Expect to spend most of the day doing it, but I like to store my plasmids in this form.

Ingredients

Ingredients are per culture; make enough for one extra culture to allow for pipetting error).

• 150μL sterile 50% glycerol
• 1mL TEG (25mM Tris-Cl, 10mM EDTA, 50mM dextrose)
• 111μL 20mg/mL lysozyme
• 2mL worth of components for solution 2: 200μL 10% SDS, 100μL 4M NaOH, 1.7 mL autoclaved water
• 1.5mL Solution 3: 3M K⁺, 5M acetate (3M potassium-acetate, 2M acetic acid --- glacial is 17M)
• 3.7mL isopropanol
• 1mL TE buffer
• 0.5mL 5M LiCl
• 7.5μL 1mg/mL RNaseA
• 200μL 70% ethanol
• several mL of phenol:chloroform:isoamyl alcohol (25:24:1)
• several mL of chloroform:isoamyl alcohol (24:1)
• 750μL straight ethanol
• 125μL 3M sodium acetate

Directions

1. Grow a single colony of E. coli overnight in 50mL LB broth + selective markers at 37°C.
2. The next morning, put 850μL of the culture in each of two Eppendorf tubes, add 150μL sterile 50% glycerol, and store at -80°C. Pour as much culture as will fit into an Oak Ridge tube and centrifuge at 5800g/6000rpm, 4°C, for 10 minutes in a GSA rotor. Discard the supernatant, add the rest of the culture, and repeat. Resuspend in 1mL TEG.
3. Add 111μL 20mg/mL lysozyme. Incubate on ice for 30 minutes. Meanwhile, mix: 250μL 10% SDS, 125μL 4M NaOH, 2.125mL autoclaved water per culture.
4. Add 2mL SDS/NaOH mix to each tube. Incubate on ice for 10 minutes.
5. Add 1.5mL Solution 3 (3M K⁺, 5M acetate). Incubate on ice for 10 minutes.
6. Shake vigorously. Centrifuge in SS34 rotor at 17,200g/12,000rpm, 4°C, for 15 minutes.
7. Pour the supernatant into another Oak Ridge tube and discard the pellet. Add 2.7mL isopropanol. Centrifuge at 17,200g/12,000rpm (room temperature) for 10 minutes. Discard the supernatant.
8. Wash pellet with 1mL 70% ethanol. Air dry for 2-5 minutes on bench. Resuspend in 500μL TE buffer. Add 500μL 5M LiCl. Incubate on ice for 5 minutes.
9. Centrifuge at 17,200g/12,000rpm for 10 minutes.
10. Pour supernatant into an Eppendorf. Add 1mL isopropanol. Incubate on the bench for 10 minutes.
11. Centrifuge at 17,200g/12,000rpm for 10 minutes.
12. Discard the supernatant. Wash the pellets with 100μL 70% ethanol. Resuspend in 375μL TE buffer. Add 7.5μL 1mg/mL RNaseA. Incubate at 37°C for 30 minutes.
13. Add 700μL phenol:chloroform:isoamyl alcohol. Vortex until thoroughly mixed. Centrifuge at top speed of microfuge for 2 minutes. Pipette aqueous phase (the top one) into new Eppendorf. Repeat until the interface between the phases is clear after centrifugation. Then repeat the procedure twice with chloroform:isoamyl alcohol to remove any phenol.
14. Add 750μL straight ethanol and 125μL 3M sodium acetate. Put at -80°C for 30 minutes or -20°C overnight.
15. Centrifuge at 13,600g/12,000rpm, 4°C, for 15 minutes. Discard the supernatant. Wash pellet with ~100μL 70% ethanol. Resuspend in 100-200μL TE buffer.