IGEM:IMPERIAL/2008/New/Growth Curve
From OpenWetWare
Current revision (08:50, 25 October 2008) (view source) 

(36 intermediate revisions not shown.)  
Line 3:  Line 3:  
<br>  <br>  
<br>  <br>  
  +  {{Imperial/Box2Growth Curve  
  +  Part of our dry lab team concentrated on modelling the growth curve of ''B. subtilis''. This is important to characterise the chassis; particularly, the growth of ''subtilis'' is a vital parameter for planning experiments for future projects. Characterisation increases the predictability of the growth of B. subtilis by determining, for example, its growth rate and the duration of its distinctive growth phases. In order to model the growth of ''B. subtilis'', the process was broken down into three main steps, where a separate submodel is produced in MATLAB for each step. Each submodel is an ODE model, which can be simulated using MATLAB. The variables in each submodel can be adjusted according to the boundary conditions (from experimental results).  
  {{Imperial/  +  
  +  In the final step, a combination of Submodels 1 and 2 are superposed with Submodel 3, resulting in a more complex model which enhances the accuracy of illustrating bacterial growth. For more details about the submodels, please click on the following links:  
  
  +  '''[[Tutorial for Growth Curve]]''' (More details about each submodel)  
  +  '''[[Media:Modelling_Growth_Curve.pdf]]''' (The tutorial questions)  
  +  
  +  
  +  
  [[  +  
  +  
  +  
  +  
  +  The graph on the right shows the log graph used to determine the growth rate.  
+  [[Image:Log_graph.tif300pxLogGraph used to determine the growth rate]]}}  
+  {{Imperial/Box1Key Phases of Bacterial Growth  
+  ===Lag Phase===  
During the lag phase, the rate of growth is slow due to two main reasons, ''B. subtilis'' is absorbing nutrients in the medium and the replication machinery is being switched on. The higher the concentration of nutrients in the medium, the faster the rate of bateria growth.  During the lag phase, the rate of growth is slow due to two main reasons, ''B. subtilis'' is absorbing nutrients in the medium and the replication machinery is being switched on. The higher the concentration of nutrients in the medium, the faster the rate of bateria growth.  
  As a result, the volume of the bacteria increases, followed by an  +  As a result, the volume of the bacteria increases, followed by an increase in the number of bacteria. 
  +  
  +  
+  === Exponential Phase ===  
Both colony number and cell volume increase exponentially during this phase. Our model assumes concentration of the nutrients inside the bacteria is constant.  Both colony number and cell volume increase exponentially during this phase. Our model assumes concentration of the nutrients inside the bacteria is constant.  
  ===  +  === Stationary Phase === 
  +  The growth of the colony ceases in number and in volume due to a finite concentration of nutrients, hence it does not have a gradient. Other causes may be death and cell division.  
  The growth of the colony ceases in number and in volume due to a finite concentration of nutrients, hence  +  
According to the model, the maximum growth of the bacteria is determined by the concentration of nutrients available initially.  According to the model, the maximum growth of the bacteria is determined by the concentration of nutrients available initially.  
Line 41:  Line 33:  
*Time span of lag phase, stationary phase and exponential phase  *Time span of lag phase, stationary phase and exponential phase  
  *The growth rate  +  *The growth rate}} 
  }}  +  
  +  {{Imperial/Box1The Model  
  +  The model illustrates the main growth phases the ''B. subtilis'' undergoes. These are identified as the '''lag phase''', the '''exponential phase''' and the '''stationary phase'''. The death phase is a constitutive event and it is possible that it exerts an influence on the three phases discussed below. However, to simplify a complicated model, it is less relevant in this case and therefore is not included in this model.  
  The model  +  
  The  +  The Mfile used to generate the model below is located in the Appendices section of the Dry Lab hub. 
  +  <center>[[Image:Nutrient ft.TIF500px]][[Image:Label_model.TIF500px]]</center>}}  
  
  +  {{Imperial/Box1Results  
+  The model for the growth curve was fitted to the experimental results as shown below. The experimental results is depicted by the red curve, while our model is shown by the green curve. The resource curve was also plotted as a function of time and is shown below. Based on our experimental results from the Wet Lab, a log graph was plotted to determine the growth rate. The growth rate was then determined from the gradient of the log graph. This value was included when simulating the growth model using MATLAB.  
+  <html><table border="0" cellpadding="5" cellspacing="0" align="center"><tr><td width=33%></html>[[Image:Experimental_Result.JPGthumbcenter]]<html>  
+  </td><td></html>[[Image:Fitted_Curve.JPGthumbcenter]]<html>  
+  </td><td></html>[[Image:Resource_Curve.JPGthumbcenter]]<html>  
+  </td></tr><tr><td><center>Experimental Results</center>  
+  </td><td><center>Fitted Curve</center>  
+  </td><td><center>Resource Curve</center>  
+  </td></tr></table></html>  
  +  The following constants used to generate the model were found to yield the best fit to experimental results.  
  
  +  GROWTH CONSTANT (A): 1.3494  
  +  
  +  
  +  
  +  
  +  
  +  
  +  
  +  
  +  
  +  
  +  
  +  
  +  INITIAL NUTRIENT CONCENTRATION (R<sub>0</sub>): 2  
  +  HILL COEFFICIENT (n): 1.25  
  +  INITIAL OD: 0.4  
  +  CONSTANT (<math>\alpha</math>): 0.64516  
+  
+  }}  
  
  
{{Imperial/EndPageDry_LabGenetic_Circuit}}  {{Imperial/EndPageDry_LabGenetic_Circuit}} 
Current revision
 
