Haynes Lab:Notebook/Investigating Photo-Switchable Synthetic Nucleosomes/2012/11/21

From OpenWetWare

(Difference between revisions)
Jump to: navigation, search
(→11/21/12)
(→11/21/12)
Line 126: Line 126:
* Incubate at 37°C/ 10 min.
* Incubate at 37°C/ 10 min.
* Heat inactivate at 75°C/ 2 min.
* Heat inactivate at 75°C/ 2 min.
-
* [final] = 200 ng/μLuL / 15 μL = ~13 ng/μL
+
* [final] = 200 ng/μL / 15 μL = ~13 ng/μL

Revision as of 17:18, 21 November 2012

Project name Main project page
Previous entry      Next entry

11/21/12

  • Repeat PCR of H2B and LOV inserts
  • Note: Primers add a XbaI site upstream and the SpeI, NotI, and PstI sites downstream
  1. H2B-GFP plasmid + BB_H2B fwd + BB_H2B rev
  2. LOV plasmid + BB_LOV fwd + BB_LOV rev
Reagents H2B LOV
Plasmid DNA 0.5 μL 0.5
primer 1 (10 μM) 1.0 1.0
primer 2 (10 μM) 1.0 1.0
2x GoTaq mix 12.5 12.5
dH2O 10.0 10.0
Total 25.0 25.0

PCR program:

  • 95°C, 3 min.
  • [95°C, 30 sec; 57°C, 30 sec.; 72°C, 30 sec.] x35 cycles
  • 72°C, 3 min.
  • 4°C ∞
Expected:
1. H2B = 410
2. LOV = 461

Results of the digests are shown. Image:KAH_Fermentas_GeneRuler_1kbplus.jpg

Results of the PCR products, with H2B on the left and LOV on the right. The gel was loaded with 5 μL samples.

  • ---Karmella 15:56, 21 November 2012 (EST): Digest, purification, and ligation

Assemblies

  1. H2B - X/S - 410 bp + pSB1A3 - X/S - 2000 bp
  • Digests:
    • In a 30 μL reaction, cut H2B with XbaI and SpeI
    • In a 30 μL reaction, cut LOV with XbaI and SpeI
Reagent H2B PCR LOV PCR
DNA 8.0 8.0
XbaI 1.0 1.0
SpeI 1.0 1.0
10x buffer 3.0 3.0
dH2O 10.0 10.0
Total vol. 30. 0 30.0


  • Run entire 30 μL on a 1% gel (use the big fat-tooth well comb)
  • Cut band out of gel (use UV box)


Results from gel recovery:

Sample 260 260/280 ng/μL
H2B - X/S ### ### ###
LOV - X/S ### ### ###


Results of from the digests are shown. Image:KAH_Fermentas_GeneRuler_1kbplus.jpg

  1. H2B = 410
  2. LOV = 461


Dephosphorylation

> Dephosphorylation (Roche)

  1. pSB1A3 - X/S =
Reagent Volume
DNA (clean digest) up to 11.0 (~200 ng)
10x buffer d.p. 1.5
phosphatase 0.5
dH2O 2.0
  15 μL
  • Incubate at 37°C/ 10 min.
  • Heat inactivate at 75°C/ 2 min.
  • [final] = 200 ng/μL / 15 μL = ~13 ng/μL


Ligation

  • Use 20 ng of vector for each ligation = 1.5 μL pSB1A3
  • Use 2x moles of H2B insert, relative to vector: xμL H2B insert = 3 * 410 bp H2B / 2000 bp pSB1A3 * 20 ng pSB1A3 / ### ng/μL H2B = 1.28 μL H2B
  • Use 2x moles of LOV insert, relative to vector: xμL LOV insert = 3 * 461 bp LOV / 2000 bp pSB1A3 * 20 ng pSB1A3 / ### ng/μL LOV = 0.8 μL LOV
  H2B LOV Negative Control
Insert DNA (2x mol vector) ### μL ### ---
Vector DNA (50 ng) 1.5 1.5 1.5
2x Roche Rapid Ligation buffer 5.0 5.0 5.0
New England Biolabs T4 ligase 1.0 1.0 1.0
dH2O ### ### ###
TOTAL 10.0 10.0 10.0
Mix the reaction(s) thoroughly by flicking the tube.
Incubate at room temperature for 10 minutes.

Proceed directly to Transformation. See http://openwetware.org/wiki/Haynes:Assembly101




Retrieved from "http://openwetware.org/wiki/Haynes_Lab:Notebook/Investigating_Photo-Switchable_Synthetic_Nucleosomes/2012/11/21"
Personal tools