Haynes:LBagarAmp

From OpenWetWare

(Difference between revisions)
Jump to: navigation, search
(New page: <- Back to Protocols <div style="width: 800px"> =LB Agar Plates= by Karmella Haynes, 2012<br><br> MATERIALS * Personal Protective Equipment (PPE) - lab coat, disp...)
(2 intermediate revisions not shown.)
Line 1: Line 1:
-
<- [[Haynes:Protocols | Back to Protocols]]
+
<- [[Haynes:Internal | Back to Personnel Page]]
<div style="width: 800px">
<div style="width: 800px">
Line 13: Line 13:
* 1N NaOH
* 1N NaOH
* Two clean and sterile 1000 mL glass flasks
* Two clean and sterile 1000 mL glass flasks
 +
* 100 mg/mL Ampicillin from the -20°C freezer (if you are making amp plates)
 +
PROCEDURE
PROCEDURE
Line 33: Line 35:
# Quickly and carefully fill each flask up to the 500 mL mark.
# Quickly and carefully fill each flask up to the 500 mL mark.
-
'''Set up the plates to be filled'''
+
'''Melt the LB Agar'''
-
# Cover the bench top with bench paper
+
# OPTION 1 - Microwave
 +
## Replace the foil caps with Kimwipe-covered black foam plugs.
 +
## Carry the flasks (in a tray) to the large white microwave (Wang Lab).
 +
## Microwave the flasks for 5 minutes. Use a rubber mitt to swirl the flasks (to remove trapped air).
 +
## Microwave the flasks for another 5 minutes. Use a rubber mitt to swirl the flasks (to remove trapped air).
 +
## Microwave the flasks for10 minutes. Use a rubber mitt to put the flasks back into the tray and bring them back to your bench
 +
# OPTION 2 - Autoclave
 +
## Put the foil caps on the flasks.
 +
## Put the flasks in an autoclave tray. Fill the bottom of the tray about 1 inch deep with tap water (this trick prevents boil-over).
 +
## Take the tray with flasks up to the 3rd floor autoclave.
 +
## Choose the "Liquid 15" program/cycle. Put the tray with flasks into the autoclave, close the door, and hit "start".
 +
 
 +
'''Set up the empty plates''' - complete this part while the LB agar is melting in the microwave or autoclave
 +
# Cover the work area with bench paper
# Get a stack of plates and cut open the very top of the sleeve. Do not rip apart the sleeve. You will need this to store the finished plates.
# Get a stack of plates and cut open the very top of the sleeve. Do not rip apart the sleeve. You will need this to store the finished plates.
-
# Take the plates out and stack them in sets of five, lid-side-up
+
# Take the plates out and stack them in sets of five, lid-side-up.
 +
# If you are making Amp plates, take a tube of 100 mg/mL ampicillin from the -20°C freezer and thaw it in your hand or at room temperature.
 +
 
 +
 
</div>
</div>

Revision as of 19:08, 21 September 2013

<- Back to Personnel Page

LB Agar Plates

by Karmella Haynes, 2012

MATERIALS

  • Personal Protective Equipment (PPE) - lab coat, disposable gloves
  • ~40 clean, sterile petri dishes (pr "plates"), packed in plastic "sleeves" per 1 liter of LB agar
  • LB Broth powder (Sigma L3022)
  • Bacteriological Agar
  • 1N NaOH
  • Two clean and sterile 1000 mL glass flasks
  • 100 mg/mL Ampicillin from the -20°C freezer (if you are making amp plates)


PROCEDURE

Make LB Agar - these instructions are for 1 liter

  1. Put on your PPE.
  2. Fill a 1000 mL graduate cylinder with deionized water (from the sink)
  3. Weigh out 20 g of LB Broth powder on the balance.
  4. Add the LB powder to the water in the cylinder.
  5. Weigh out 15 g of Bacteriological Agar.
  6. Add the Bacteriological Agar to the mixture in the cylinder.
  7. Use a 1000 μL micropipette to add 1000 μL 1N NaOH to the mixture.
  8. Swirl the mixture for a few seconds.
  9. Fill the cylinder up to 1000 mL with deionized water (from the sink).
  10. Get two clean, sterile 1000 mL glass flasks from the shelf. Remove the foil caps and set them aside
  11. Carefully cover the cylinder with a large square of parafilm. Make sure the seal is tight.
  12. Cover the opening with your gloved hand and invert the cylinder several times to mix the solution.
  13. Quickly and carefully fill each flask up to the 300 mL mark. Cover the cylinder again and invert to mix.
  14. Quickly and carefully fill each flask up to the 400 mL mark. Swirl the cylinder to mix.
  15. Quickly and carefully fill each flask up to the 500 mL mark.

Melt the LB Agar

  1. OPTION 1 - Microwave
    1. Replace the foil caps with Kimwipe-covered black foam plugs.
    2. Carry the flasks (in a tray) to the large white microwave (Wang Lab).
    3. Microwave the flasks for 5 minutes. Use a rubber mitt to swirl the flasks (to remove trapped air).
    4. Microwave the flasks for another 5 minutes. Use a rubber mitt to swirl the flasks (to remove trapped air).
    5. Microwave the flasks for10 minutes. Use a rubber mitt to put the flasks back into the tray and bring them back to your bench
  2. OPTION 2 - Autoclave
    1. Put the foil caps on the flasks.
    2. Put the flasks in an autoclave tray. Fill the bottom of the tray about 1 inch deep with tap water (this trick prevents boil-over).
    3. Take the tray with flasks up to the 3rd floor autoclave.
    4. Choose the "Liquid 15" program/cycle. Put the tray with flasks into the autoclave, close the door, and hit "start".

Set up the empty plates - complete this part while the LB agar is melting in the microwave or autoclave

  1. Cover the work area with bench paper
  2. Get a stack of plates and cut open the very top of the sleeve. Do not rip apart the sleeve. You will need this to store the finished plates.
  3. Take the plates out and stack them in sets of five, lid-side-up.
  4. If you are making Amp plates, take a tube of 100 mg/mL ampicillin from the -20°C freezer and thaw it in your hand or at room temperature.



Personal tools