Griffin: Ultimate Immunoprecipitation Guide
If you are planning on performing an IP experiment, then consider to run a preliminary western blot first in oder to get a feel for what the antibody is capable of binding.
RIPA (Radio ImmunoPreciptation Assay) buffer is a traditional name for an array of recipes that have found success over the years. Below are details that can contribute to optimizing your immunoprecipitation experiment. Lysis buffer components can and will influence the efficiency of the IP reaction. Detergent composition is a major factor for IP reactions. Adjusting salt concentration and detergent composition will influence the efficiency of the IP reaction. Membrane bound proteins (proteins based in lipid rafts), protein complexes, and protein charge can all influence the efficient yield of your gene product in the lysate prep.
Common RIPA components
PBS : Salt prevents non-specific protein aggregation
Tris-HCl : Buffering agent prevents protein denaturation
1% Nonidet P-40 or Igepal CA-630 : Non-ionic detergent to extract proteins, form lipid micelles
1% Triton X-100 : Non-ionic detergent to extract proteins, form lipid micelles - to use in place of Nonidet/Igepal
0.5% sodium deoxycholate : Ionic detergent to extract membrane protein and isolate lipids
0.1% SDS : Ionic detergent to extract membrane protein and isolate lipids
Na3VO4 (Sodium Orthovanadate) : Tyrosine phosphatase Inhibitor; hydrostatic interference of active sights of phosphatases
Misc. Phosphatase Inhibitors: Phosphorylation/dephosphorylation of proteins influences the charge-charge relationships that proteins have with eachother in solution. Proteins undergo covalent attachment of a phosphoryl group (phosphorylation) typically at serine, threonine, or tyrosine residues. Phosphate groups are removeable via protein phosphatases. During the extraction of phosphorylated proteins from cell and tissue, preserving the phosphorylation states of total protein is a good technique.
RIPA Buffer Recipes
These may be made in large volumes. Add inhibitors fresh at time of use from stock solutions
Lysis Buffer I: A tried and true lysis buffer for most signaling intermediates and soluble/cytosolic factors.
- 1x PBS
- 1% Nonidet P-40
- 0.5% sodium deoxycholate
- 0.1% SDS, PMSF, Aprotinin
- 100 mM Na3VO4 Sodium orthovanadate activation
- 10 mg/ml PMSF (200 mM) in isopropanol (add at 10 µl/ml RIPA)
Lysis Buffer II: An SDS free lysis buffer to consider with Co-IP approaches. Used this one in graduate school to IP EGFR effectively.
- 150 mM NaCl
- 50 mM Tris-HCl pH 7.4
- 1% Nonidet P-40
- 0.25% Sodium Deoxycholate
- 1 mM EGTA
- 1mM PMSF
- 1 ug/ml of Aprotinin, Leupeptin, Pepstatin,
- 1 mM Na3VO4
- 1mM NaF
Lysis Buffer III: This recipe calls for Brij 35 which is a non-ionic detergent, great for dissociating membrane complexes and essentially much gentler than SDS. This is also a great lysis buffer for phospho-proteins.
- 10 mM KPO4 (phosphate buffer)
- 1 mM EDTA (chelate)
- 5 mM EGTA (chelate)
- 10 mM MgCl2 (chelate)
- 50 mM †-glycerophosphate (inhibits serine-threonine phosphotase activity)
- 0.5% NP-40 (stabilizer of proteins/enzymes)
- 0.1% Brij 35 (non-ionic detergent)
- 0.1% deoxycholic acid (non-ionic, non-denaturing detergent)
- 1 mM sodium orthovanadate (inhibits tyrosine phosphotase activity)
- 1 mM phenylmethylsulfonyl fluoride (protease inhibitor again)
- 5 µg of leupeptin/mL (serine proteinase inhibitor)
- 10 µg of pepstatin/mL (another proteinase inhibitor)
- Roux PP, Richards SA, and Blenis J. . pmid:12832467.
Below is a procedure for adherent cells (ie A431, A549, Hela, NIH3T3)
I) Remove culture medium and rinse a subconfluent, 100 mm cell culture plate (80% confluent plate yields ~600-1000 microg protein total) with PBS at room temperature. The following steps should be performed on ice or at 4° C using fresh, ice cold buffers.
II) Add 0.8 ml of ice cold fresh RIPA buffer to the 100 mm cell culture plates OR 0.5 ml per 5 x 10e6 cells/60 mm dish.
III) Gently rock plates for 15 minutes at 4° C or let the plates set on ice. This step will allow the lysis buffer to act on the cells and will increase the total yield of soluble protein.
IV) For monolayer cells, do a trypsin treatment to lift cells off the flasks prior to cell lysis, instead of scraping the cells for a more gentle approach. OR Scrape the adherent cells with a cell scraper and then transfer the scraped lysate into a sterile microcentrifuge tube. Place the tube on ice.
V) Sonicate each sample on a 70% duty cycle or less by placing only the very tip of the pin into the vial, then slowly lowering it into the lysate until it foams completely and then stop. Alternatively, pass the lysate through a 21 gauge needle to shear the DNA & incubate 30–60 minutes on ice.
VI) Microcentrifuge cell lysates at 12,000xg for 15 minutes at 4°C.
I) Incubate cell lysate (500-1000 ug) with (2-5 µg) primary antibody (optimal antibody concentration should be determined by titration) for 2 hours at 4°C.
Protein A-Agarose : specific binding to mouse IgG2a, IgG2b and IgA, rabbit polyclonal Abs, human IgG1, IgG2 and IgG4
Protein G-Agarose : specific binding to mouse IgG1, IgG2a, IgG2b, IgG3, rat IgG1, IgG2a, IgG2b and IgG2c, rabbit and goat polyclonal Abs, human IgG1, IgG2, IgG3 and IgG4
III) Cap tubes and incubate at 4 C on a rocker platform or rotating device for 2 hour to overnight.
IV) Collect pellet by centrifugation at 2,500 rpm (approximately 1,000xg) for 5-10 seconds. A touch spin will work. With enough samples, gravity will pellet the beads as well.
V) Carefully aspirate and discard supernatant. The trick here is to slowly aspirate with the needle touching just the top of the liquid and slowly draw down so that the needle is pulling at the surface tension of the supernatant. This will ensure no loss of beads.
VI) Wash pellet 3 times with either RIPA buffer (more stringent) or PBS (less stringent), each time repeating centrifugation step above.
VII) After final wash, aspirate and resuspend pellet in 40 µl of 2x electrophoresis sample buffer. Or elute proteins with an appropriate antibody elution buffer.
VIII) Boil samples for 2 minutes. Load sample.