Immunohistochemistry Protocol 1
The procedure below has been proven to be effective for labeling of PECAM-1, ICAM and VCAM using validated antibodies.
Deparaffinize and rehydrate
5 min tray
2 x xylene
2 x absolute ETOH
2 x 95 % ETOH
2 x 70 % ETOH
2 x milliQ H2O
Quench endogenous peroxidase activity
200 ml methanol + 3 ml (30% H2O2) in slide tub
- make just before use, Incubate 30 minutes, RT
- wash H2O 5 min room temp.
Solution (Vector Labs; 4oC) OR other antigen retrieval techniques
- Shake well before measuring
- 320 milliQ H2O + 3 ml unmasking solution
- Mix by inversion
1. Rinse in milliQ H2O in tub
2. In slide tub with “fill” mark, fill all 24 slots in slide holder with “blank slides” if necessary, add unmasking solution to fill line, COVER and microwave for 20 minutes Replenish with dH20 at:
- 15 minutes remaining
1. Cool slides in tub, covered, at room temp for 1 hour
2. During 1 hour, make up 0.5% FSGO (fish skin gelatin oil) in PBS (1 500 ml bottle PBS + 2.5 ml FSGO; allow 15 min for FSGO to come out of pipet)
3. Transfer to tub with plain room temperature PBS, 5 min
4. Make up avidin blocking solution:
For 1 ml:
- 1 ml PBS/FSGO
- 100 ul normal serum of same species as secondary antibody
4 drops avidin blocking solution (Vector Labs)
- Invert tube to mix
5. Circle vessels with ‘pap pen’ ALWAYS KEEP SLIDES MOIST
6. Add blocking solution within circles; 1 hour in humidified chamber at room temperature
7. Aspirate off blocking solution
8. Add primary antibody to vessels on slides.
For 4 slides: antibody
- PBS/FSGO 1 ml
- normal serum 100 ul
- biotin blocking solution (Vector Labs) 4 drops
9. Incubate 4 oC overnight in humidified chamber.
1. Aspirate primary antibody solution and wash in FSGO/PBS in tub for 5 min at room temperature; agitate 2. Make up secondary antibody:
- 5 ul secondary antibody
- 100 ul normal serum
- 1 ml FSGO/PBS
3. Blot slides with kimwipe and apply secondary antibody; incubate in humidified chamber 1 hour, room temperature
4. During incubation, make up ABC solution from kit: per ml:
- 1 ml plain PBS
- 20 ul A solution
- 20 ul B solution
Allow to rock at room temperature for at least 30 min in order to form complex
5. Aspirate secondary antibody solution and wash in FSGO/PBS in tub for 5 min at room temperature; agitate
6. Blot slides and apply ABC; incubate 30 min at room temperature
7. Make up DAB solution:
Approximately 30 min before using; add H2 O2 just before use
- 10 ml plain PBS
- 1 DAB tablet
- 7.5 ul H2O2 (30%)
Test DAB and ABC by adding small amount of DAB to a small amount of left over ABC, should turn dark brown immediately.
8. Wash with agitation in plain PBS, 5 min room temperature
9. Blot slides and apply DAB solution, incubate 5 min room temperature
10. Wash in dH20, 5 min room temperature
In filtered (#1 Whatman filter paper) Hematoxylin I (not Mayer’s); 4-5 min
12. Rinse in running tap water until clear, 4-5 min. Return hematoxylin to bottle for reuse.
If needed for 1 min; wash in tap water
- Acid alcohol: 1% HCl in 50% EtOH
- Bluing reagent: commercially available (Fisher, VWR, Sigma, etc)
Procedure: Dip slides quickly in acid alcohol and immediately wash with tap water (or squirt water on the slides) Dip slides briefly in Bluing Reagent. Wash slides with tap water and continue with the IHC staining procedure(i.e., dehydrate stained tissues and mount the slides).
0.1% Sodium Bicarbonate
- Sodium bicarbonate --------------------------- 1 g
- Distilled water --------------------------------- 1000 ml
Mix to dissolve. The pH will be around 8.0 Store this solution at room temperature.
Note: this solution worked better than ammonia water solution according to testing result. Bluing for 30 seconds to 1 minute after hematoxylin staining and clearing/differentiation.
0.2% Ammonia Water Solution (Bluing)
- Ammonium hydroxide (concentrated) ------ 2 ml
- Distilled water -------------------------------- 1000 ml
Mix well. The pH will be around 10.0 Store this solution at room temperature.
Note: this solution is not as good as sodium bicarbonate according to testing result. Bluing for 30 seconds to 1 minute after hematoxylin staining and clearing/differentiation.
Lithium Carbonate Solution (Saturated)
- Lithium carbonate ---------------------------- 1.54 g
- Distilled water -------------------------------- 100 ml
Mix to dissolve and store at room temperature. Bluing for 30 seconds to 1 minute after hematoxylin staining and clearing/differentiation.
5 minutes each:
- 3 x absolute ETOH
- 2 x xylene
Abbreviated Immunohistochemistry Protocol
1. Deparaffinize and rehydrate 5 min tray
2 x xylene
2 x absolute ETOH
2 x 95 % ETOH
2 x 70 % ETOH
2 x milliQ H2O
3. Rinse sections in 2 changes of PBS washing buffer in separate beakers, 2 minutes each.
4. Serum Blocking: incubate sections with 10% normal serum blocking solution for 30 minutes to block non-specific binding of immunoglobulin.
5. Primary Antibody: incubate sections with Primary antisera diluted 1:50 in 3% serum PBS, for 1 hour at room temperature to overnight 4C.
6. Rinse in PBS washing buffer for 2 x 2 min.
7. Secondary Antibody: incubate sections with conjugated secondary antibody 1:100-500 in 3% serum PBS, for 1 hour at room temperature.
8. Rinse in PBS washing buffer for 3 x 2 min.
9. Counter-stain in Gill´s formulation #2 hematoxylin for 5–10 seconds. Immediately wash with several changes of deionized H2O.
10. Dehydrate: Soak in 95% ethanol 2x10 seconds, then 100% ethanol 2x10 seconds, then xylenes 3x10 seconds. Pipet 1–2 (5ul) drops of permanent mounting medium, cover with a glass coverslip and observe by light microscopy.
- Chromogen only; no primary or secondary antibody
- Conjugate and chromogen control; no primary
- Biotinylated antibody, conjugate, chromogen control
- Isotype control ( for monoclonal antibodies only)
- Species control (ie. incubation with normal goat IgG)
- Absorption control
Preventing tissues from peeling off the slide
- Insufficient fixation or unfixed tissues tend to come off slides more easily. Fix tissues longer to get completely fixation of tissues.
- Formaldehyde fixed frozen sections are more prone to falling off slides. Try to dry slides for much longer time or use alternative fixation such as acetone or alcohol.
- Tissue sections tend to come off slides more often on regular slides (uncharged or uncoated). Always use positively charged or coated slides for immunostaining.
- You may just have had a bad batch of slides. Replace with a new batch of slides.
- The disposable blades have oil on them. Clean disposable blades with xylene.
- Wrinkles presented in the sections during the initial mounting. Try to spread the sections out and mount the sections on slides with wrinkle free.
- Paraffin sections may not be dried completely before placing in the oven. Allow paraffin sections to air dry at least 30 minutes before placing in the oven at 56 C overnight.
- Frozen sections may not be dried completely before fixation and immunostaining procedure. Allow frozen sections to air dry for at least 30 minutes before fixation and then air dry for another 30 minutes before immunostaining.
- Antigen retrieval procedure can cause sections to come off slides, especially when EDTA (pH8.0) or Tris-EDTA (pH9.0) such high pH antigen retrieval solution is used. Use low pH solution such as citrate buffer (pH6.0) antigen retrieval Solution to replace EDTA (pH8.0) or Tris-EDTA (pH9.0) retrieval solution if it is possible.
- Distilled water alone may make sections come off slides easy. Always use buffer solution to wash or rinse slides.
- Bone (especially the cartilage) tends to fall off slides after heat treatment. Try other alternative retrieval methods such as enzyme digestion.
- Antigen retrieval devices may be trouble. Try to use waterbath or steamer in stead of microwave or pressure cooker.
- Plain water in waterbath for mounting paraffin sections. Add some gelatin in waterbath for mounting paraffin sections.
- If you have tried everything above and the problem persists. Try gelatin coated slides and it has been working fairly well.
Avidin versus Streptavidin
Both Avidin and Streptavidin are suitable for binding to secondary biotin-conjugated antibodies.
- Avidin is a tetrameric protein originally isolated from chicken egg white with a MW of about 67K and an isoelectric point of about 10.
- Streptavidin is a biotin binding protein isolated from cultures of Streptomyces avidinii. It has Avidin-like binding characteristics; however, it has a MW of about 16K and an isoelectric point of 5-6.
One mole Avidin will bind four mole biotin. The high pI of Avidin can cause binding to acidic structures such as DNA. Biotin is a naturally occurring vitamin with a MW of 244.31 and an isoelectric point of 3.5. The Avidin-Biotin interaction is the strongest known non covalent, biological interaction (Ka=1015 M-1). The bond formation is rapid and is unaffected over wide range of pH.