Biomod/2013/Komaba/Design: Difference between revisions
Toyoki Kondo (talk | contribs) |
Toyoki Kondo (talk | contribs) No edit summary |
||
| Line 2: | Line 2: | ||
== Cylinder == | == Cylinder == | ||
The cylinder is put in the center of the motor as an axis supporting the rotation. DNA strands of staples and a scafold are formed into a cylindrical shape using DNA Origami technology. It was designed with cadnano software, which "simplifies and enhances the process of designing three-dimensional DNA origami nanostructures"(Figure 1). In order to bind footing DNAs on its surface spirally, 10mer long DNA strands, called probes, are jutting out from the cylinder's surface. After the cylinder with the probes is formed, anchor of DNA spiders is hybridized to a specific strand at the start point on the cylinder's surface. Then the footings get connected to the probes. The footing tracks, each of which consists of three lanes of the footings, enable DNA Spiders to orbit the cylinder. In detail, there are two tracks of DNA footings and two spiders walk on each track. In addition, in order to make it easy to observe the direction of spiders' walk, a small sub-cylinder is attached at the end of the footing tracks(Figure 2). The diameter of the cylinder is 25.4 nm and height is 43.5 nm. This is calculated considering that the cylinder can be observed with an Atomic Force Microscope and that the interval between the two tracks are wide enough for spiders not to jump to next footing track (Figure 3). | |||
(Figure | |||
== DNA Spider == | == DNA Spider == | ||
Our DNA screw rotates by using DNA spiders, which is being created based on the work of Lund, et al. DNA spider is connected to the DNA ring by a “head” strand, and also DNA spider's legs are connected to strands on the surface of the DNA cylinder. DNA spider consists of a body, a head, an anchor, and three legs, all of which are going to be made by DNA. These legs advance by cutting strands with DNAzyme. DNAzyme is a DNA which cuts DNA strands like enzymes do. Because the spider's track is a spiral, DNA rings rotates as DNA spiders walk. The head is complementary to the strand stretching from a ring made of DNA. | |||
In detail, legs and the footings are complementary strands. The footings are attached spirally to the surface of the DNA cylinder and function as a substrate of the DNA spider. DNA spiders normally move one way. Once DNAzyme cuts the tip of the footings, DNA spiders are disconnected to the footings. The footing is binding to the nearest track strand and the cutting process is occurring again. | |||
We will use the same DNA spider’s sequences as the way Lund, et al. did; 5’ - TCT CTT CTC CGA GCC GGT CGA AAT AGT GAA AA – 3’. We are developing the body sequence of the DNA spider. When we decide them, we will order them as soon as possible. | |||
== Rotary Ring == | == Rotary Ring == | ||
It is the DNA ring that actually rotates. It has a shape of a cylinder short in the axial direction and is also composed with DNA Origami technology. We made the structure using cadnano (Figure4). Two 10mer long strands come up from the inner side of the ring and are connected to the DNA spiders. The diameter of the ring is 50.9 nm, and so it can hold the cylinder and spiders inside of the ring. The thickness of ring is 10.9 nm in consideration of Atomic Force Microscope visibility (Figure 5). | |||
== DNA Screw (Combination of above parts) == | == DNA Screw (Combination of above parts) == | ||
The DNA screw is realized by assembling the above four parts: the cylinder, footings, DNA Spiders, and the rotary ring (Figure 6). | |||
Revision as of 00:57, 10 September 2013
Home,Project,Design,Experiment,Supplementation,Team,Sponsors
Cylinder
The cylinder is put in the center of the motor as an axis supporting the rotation. DNA strands of staples and a scafold are formed into a cylindrical shape using DNA Origami technology. It was designed with cadnano software, which "simplifies and enhances the process of designing three-dimensional DNA origami nanostructures"(Figure 1). In order to bind footing DNAs on its surface spirally, 10mer long DNA strands, called probes, are jutting out from the cylinder's surface. After the cylinder with the probes is formed, anchor of DNA spiders is hybridized to a specific strand at the start point on the cylinder's surface. Then the footings get connected to the probes. The footing tracks, each of which consists of three lanes of the footings, enable DNA Spiders to orbit the cylinder. In detail, there are two tracks of DNA footings and two spiders walk on each track. In addition, in order to make it easy to observe the direction of spiders' walk, a small sub-cylinder is attached at the end of the footing tracks(Figure 2). The diameter of the cylinder is 25.4 nm and height is 43.5 nm. This is calculated considering that the cylinder can be observed with an Atomic Force Microscope and that the interval between the two tracks are wide enough for spiders not to jump to next footing track (Figure 3).
DNA Spider
Our DNA screw rotates by using DNA spiders, which is being created based on the work of Lund, et al. DNA spider is connected to the DNA ring by a “head” strand, and also DNA spider's legs are connected to strands on the surface of the DNA cylinder. DNA spider consists of a body, a head, an anchor, and three legs, all of which are going to be made by DNA. These legs advance by cutting strands with DNAzyme. DNAzyme is a DNA which cuts DNA strands like enzymes do. Because the spider's track is a spiral, DNA rings rotates as DNA spiders walk. The head is complementary to the strand stretching from a ring made of DNA.
In detail, legs and the footings are complementary strands. The footings are attached spirally to the surface of the DNA cylinder and function as a substrate of the DNA spider. DNA spiders normally move one way. Once DNAzyme cuts the tip of the footings, DNA spiders are disconnected to the footings. The footing is binding to the nearest track strand and the cutting process is occurring again.
We will use the same DNA spider’s sequences as the way Lund, et al. did; 5’ - TCT CTT CTC CGA GCC GGT CGA AAT AGT GAA AA – 3’. We are developing the body sequence of the DNA spider. When we decide them, we will order them as soon as possible.
Rotary Ring
It is the DNA ring that actually rotates. It has a shape of a cylinder short in the axial direction and is also composed with DNA Origami technology. We made the structure using cadnano (Figure4). Two 10mer long strands come up from the inner side of the ring and are connected to the DNA spiders. The diameter of the ring is 50.9 nm, and so it can hold the cylinder and spiders inside of the ring. The thickness of ring is 10.9 nm in consideration of Atomic Force Microscope visibility (Figure 5).
DNA Screw (Combination of above parts)
The DNA screw is realized by assembling the above four parts: the cylinder, footings, DNA Spiders, and the rotary ring (Figure 6).
