BME103:T930 Group 6
|BME 103 Fall 2012|| Home |
Lab Write-Up 1
Lab Write-Up 2
Lab Write-Up 3
Course Logistics For Instructors
Wiki Editing Help
LAB 1 WRITE-UP
(Please finish by 11/7/2012)
Initial Machine Testing
The Original Design
Experimenting With the Connections
When we unplugged (part 3) from (part 6), the machine ... (did what? fill in your answer)
When we unplugged the white wire that connects (part 6) to (part 2), the machine ... (did what? fill in your answer)
(Write the date you first tested Open PCR and your experience(s) with the machine)
Polymerase Chain Reaction
Polymerase Chain Reaction (PCR) is a biochemical process the replicates and amplifies a desired sequence of DNA. The original DNA strand is pulled apart and primer marks the location of the targeted DNA sequence for polymerase to begin replication of the complementary strands. This process is continued until there are an exponentially increasing amount of the desired strand, allowing it to be closely examined.The PCR reaction relies on thermal cycling, in which repeated cycles of cooling and heating the samples enable the enzymes to appropriately replicate the targeted strand, and carry out the processes previously described.
1. Obtain DNA sample and label them clearly.
2. Using a micro-pipette, transfer the proper amounts of forward primers, reverse primers, dNtP's and Taq Polymerase master mix to each the 8 labeled DNA sample tubes. Be sure to replace the pipette tip after every transfer to avoid contamination.
3. Place the DNA sample tubes into the Open PCR machine.
4. Close lid and tighten screw until it touches the tops of the tubes.
5. Program the machine to run the following cycles:
- Stage 1: 1 cycle, 95 degrees Celsius for 3 minutes
- Stage 2: 30 cycles, 95 degrees for 30 seconds, 57 degrees for 30 seconds, 72 degrees for 30 second
- Stage 3: 72 degrees for 3 minutes
- Final Hold: 4 degrees
GoTaq® DNA Polymerase is supplied in 2X Colorless GoTaq® Reaction Buffer (pH 8.5), 400μM dATP, 400μM dGTP, 400μM dCTP, 400μM dTTP and 3mM MgCl2.
The eight samples that were tested consisted of a positive and negative control. The other six had three DNA samples from one patient and three DNA samples from the second patient. The first patient has an ID of 51919, and is a female that is fifty-four years of age. The second patient has an ID of 60627, and is also a female, but with an age of sixty-three.
(Add your work from Week 3, Part 2 here)
Research and Development
Specific Cancer Marker Detection - The Underlying Technology
Polymerace chain reaction (PCR) is a biochemical technology that is used to amplify a specific piece of DNA by generating thousands to millions of copies of a particular DNA sequence. The method relies on thermal cycling by heating and cooling the DNA so that the double strands break apart and can be replicated.
What are the component of a PCR reaction?
Template DNA: A specific DNA sequence that is trying to be detected.
Primers: A short segment of DNA sequences that is complementary to the target DNA sequence and binds to the targeted nucleotides.
Taq Polymerase: An enzyme that is active at high temperature that begins at the primer and takes complementary nucleotides from the solution and binds them to the "unzipped" strands.
Magnesium Chloride: A cofactoe that attaches to the Taq Polymerase to affect the speed of the reaction.
dNTP's: Deoxynucleotide triphosphates; individual nucleotide bases in that solution that are attached to the replicated DNA strands by Taq Polymerase.
What happens during each step of the thermal cycle?
The r17879961 cancer-associated sequence begining tested for is AAACTCTTACACTGCATACA. The bolded C represents the cancer gene that appears because the C took the place of the normal T that should be present. The one nucleotide base that was changed results in producing the amino acid of threonine instead of isoleucine. Because of the change in the amino acid begin produced, a study in Finland has found that this sequence has been link to susceptibility to colorectal cancer. Of the patients tested, 7.8% of the patients with colorectal cancer had the allele while 5.3% of patients without colorectal cancer had the same allele.
Why does a cancer gene produce a positive result while a normal gene produces a negative?
Relation to Bayers' Rule: Bayers' rule is used to determine the probability of true positives, false positives, and false negatives to predict the reliability of the process in detecting the cancer sequence in patients.
(BONUS points: Use a program like Powerpoint, Word, Illustrator, Microsoft Paint, etc. to illustrate how primers bind to the cancer DNA template, and how Taq polymerases amplify the DNA. Screen-captures from the OpenPCR tutorial might be useful. Be sure to credit the source if you borrow images.)
(Your group will add the results of your Fluorimeter measurements from Week 4 here)