BME103:T130 Group 12 l2

From OpenWetWare

(Difference between revisions)
Jump to: navigation, search
(Protocols)
(Protocols)
Line 127: Line 127:
'''6.''' After setting up the Flourimeter and the samples set a Smartphone’s photo settings to the ones listed.
'''6.''' After setting up the Flourimeter and the samples set a Smartphone’s photo settings to the ones listed.
-
Inactivate the flash
+
# Inactivate the flash
-
Set ISO To 800 (or higher if possible)
+
# Set ISO To 800 (or higher if possible)
-
Set White Balance to Auto
+
# Set White Balance to Auto
-
Set Exposure to Highest Setting
+
# Set Exposure to Highest Setting
-
Set Saturation to the Highest Setting
+
# Set Saturation to the Highest Setting
-
Set Contrast to Lowest Setting
+
# Set Contrast to Lowest Setting
'''7.''' Place the Flourimeter in the light box.
'''7.''' Place the Flourimeter in the light box.

Revision as of 23:54, 28 November 2012

BME 103 Fall 2012 Home
People
Lab Write-Up 1
Lab Write-Up 2
Lab Write-Up 3
Course Logistics For Instructors
Photos
Wiki Editing Help
Image:BME494_Asu_logo.png

Contents

OUR TEAM

Name: JamesOpen PCR machine engineer
Name: James
Open PCR machine engineer
Name: Heidi HallOpen PCR machine engineer
Name: Heidi Hall
Open PCR machine engineer
Name: Justin Landstrom StudentProtocol Planner
Name: Justin Landstrom Student
Protocol Planner
Name: ChaioProtocol Planner
Name: Chaio
Protocol Planner
Name: Jakob WellsR&D scientist
Name: Jakob Wells
R&D scientist

LAB 2 WRITE-UP

Thermal Cycler Engineering

Our re-design is based upon the Open PCR system originally designed by Josh Perfetto and Tito Jankowski.


New System Design
The two parts below that will be removed are the the knob and the bolt attached to it. These parts are present on the lid currently as a tightening mechanism but they will be removed to improve the design. On the side of the picture are the two heating plates present in the lid. To compensate for removing the tightening mechanism, the plates will be lowered to the point it makes contact with the samples in the heating block at the correct point in which the lid snaps into place. Image:HWAcW.jpg

Below is the top part of the general body of the PCR machine. It will be altered so buttons can be placed next to the LED screen.

Image:What?.jpg

Key Features
The design changes are predominately focused on the lid and the top body part next to the LED screen. Regarding the lid, the tightening mechanism was deemed ineffective due to not knowing how much to tighten the knob. To compensate for removing the mechanism, the heating plates will be lowered onto a specified height that it will make contact with the samples when the lid snaps into its natural place. Since sample containers are universally similar, one specified height will relinquish the need of having to set the heating plates themselves.

Design changes on the top body part will include changing the layout so that it may fit input buttons that will be connected and programmed internally later. These buttons will allow an individual to set up cycling details and will remove the need of an external computer to run the device.


Instructions


For the lid design

1. Remove the knob on the lid
2. Once the knob is removed, the bolt will be able to be removed.
3. Lower the bottom heating plate to the desired height
4. Lower the higher heating plate so the difference in space between the two plates was similar as before

For the top body part


1. Attach the part as you would normally
2. Connect the input buttons to the circuit board.





Protocols

Materials

Supplied in the Kit Amount
PCR Machine (assembled) 1
Power Cord1
Flourimeter Box1
Flourimeter1
Hydrophobic Slides5
Supplied by User Amount
Camera Phone 1
DNA Samples & Target MixAs many as desired
Bulb pipettesAs many as desired
SYBR GreenAs much as desired
Computer w/ ImageJ Software1



PCR Protocol


DNA Measurement Protocol

1. With a permanent marker, number your transfer pipettes at the bulbs so that you only use if for one sample. With the permanent marker number your Eppendorf tubes at the top.

2. Transfer each sample seperatly (using one pipette per sample) into an Eppendorf tube containing 400 mL of buffer. Label this tube with the number of your sample. Get your entire sample into this Eppendorf tube. You can use this sample number transfer pipette to place only this sample drop onto the fluorescent measuring device.

3. Take the specially labeled Eppendorf tube containing Sybr Green I using the specifically labeled pipette only place two drops on the first two centered drops as seen on the video.

4. Now take your diluted sample and place two drops on top of the Syber Green I solution drops.

5. Align the light going through the drop, as seen in the video.

6. After setting up the Flourimeter and the samples set a Smartphone’s photo settings to the ones listed.

  1. Inactivate the flash
  2. Set ISO To 800 (or higher if possible)
  3. Set White Balance to Auto
  4. Set Exposure to Highest Setting
  5. Set Saturation to the Highest Setting
  6. Set Contrast to Lowest Setting

7. Place the Flourimeter in the light box.

8. Let the smart-phone operator take as many pictures using the light box as he/she wants. Their goal is to take pictures clear enough so ImageJ can take data from the images.

9. Once they have taken enough photos of that sample give the Flourimeter back to the sample preparer to prepare the next sample.

10. Now either rerun the sample again or discard that sample and it’s pipette. Keep the Sybr Green I labeled pipette.

11. Repeat this procedure for all the samples. You can run 5 samples per glass slide.

12. As the last sample run the water from the scintillation vial as a blank using the same procedure as with the other samples.

Research and Development

Background on Disease Markers

HIV is a virus that causes A.I.D.S. (acquired immunodeficiency syndrome). HIV affects the immune system by attacking specific cells that help the immune system work. These include the T Cells that help the white blood cells fend off bacteria, disease, and viruses. A SNP related HIV is rs1024611 and it affects Chromosome 17. http://www.ncbi.nlm.nih.gov/projects/SNP/snp_ref.cgi?rs=1024611



Primer Design

The primer that can be used to detect HIV is ATA and its reverse TAT. A diseased allele will only give results because of the way the PCR works and how the primers will attach. If the sample has the disease then the primer will attach to the DNA and as the PCR goes through its cycles there will be a multitude of the same DNA strand with the SNP rs1024611. If the sample does not have the disease allele then there will be no interaction with the DNA and the primer, therefore there will be no change from the original and the end results.



Illustration


Personal tools