Aseptic Technique

From OpenWetWare

(Difference between revisions)
Jump to: navigation, search
(New page: Aseptic Technique • Protect eyes, mucous membranes, open cuts and wounds from contact with biohazard material. • Use gloves, goggles, mask, and protective clothing as necessary. ...)
Current revision (15:05, 8 September 2009) (view source)
(Aseptic Technique)
 
(3 intermediate revisions not shown.)
Line 1: Line 1:
-
Aseptic Technique
+
= Aseptic Technique =
 +
 
 +
• Protect eyes, mucous membranes, open cuts and wounds from contact with biohazard material
-
• Protect eyes, mucous membranes, open cuts and wounds from contact with
 
-
  biohazard material.
 
• Use gloves, goggles, mask, and protective clothing as necessary.
• Use gloves, goggles, mask, and protective clothing as necessary.
 +
• Carry out all culturing operation in a laminar flow hood.
• Carry out all culturing operation in a laminar flow hood.
 +
• Disinfect all surfaces prior to use with a disinfectant solution.
• Disinfect all surfaces prior to use with a disinfectant solution.
 +
• Swab down the working surface liberally with 70% ethanol.
• Swab down the working surface liberally with 70% ethanol.
-
• Periodically spread a solution of 70% ethanol over the exterior of gloves to  
+
 
-
  minimize contamination.  Replace them if torn.
+
• Periodically spread a solution of 70% ethanol over the exterior of gloves to minimize contamination.  Replace them if torn.
-
• In case of any spill, spread a solution of 70% alcohol and swab immediately with
+
 
-
  non-linting wipes.
+
• In case of any spill, spread a solution of 70% alcohol and swab immediately with non-linting
-
• Discard gloves after use and do not wear them when entering any other lab area.  
+
wipes.
-
  Bring into the work area only those items needed for a particular procedure.
+
 
-
• Leave a wide clear space in the center of the hood (not just the front edge) to work
+
• Discard gloves after use and do not wear them when entering any other lab area. Bring into the
-
  on.  Do not clutter the area to prevent blockage of proper air flow and to  
+
work area only those items needed for a particular procedure.
-
  minimize turbulence.
+
 
-
• Swab with 70% alcohol all glassware (medium bottles, beakers, etc.) before  
+
• Leave a wide clear space in the center of the hood (not just the front edge) to work on.  Do not  
-
  placing them inside the hood.
+
clutter the area to prevent blockage of proper air flow and to minimize turbulence.
-
• Arrange the work area to have easy access to all of it without having to reach  
+
 
-
  over one item to get at another (especially over an open bottle or flask).
+
• Swab with 70% alcohol all glassware(medium bottles, beakers, etc.)before placing them inside the
-
• Use sterile wrapped pipettes and discard them after use into a biohazard waste
+
hood.
-
  container.
+
 
 +
• Arrange the work area to have easy access to all of it without having to reach over one item to  
 +
get at another (especially over an open bottle or flask).
 +
 
 +
• Use sterile wrapped pipettes and discard them after use into a biohazard waste container.
 +
 
• Check that the wrapping of the sterile pipette is not broken or damaged.
• Check that the wrapping of the sterile pipette is not broken or damaged.
 +
• Inspect the vessels to be used:
• Inspect the vessels to be used:
-
T-flask – Must be free from visible contamination or breakage, or lack container
+
 
-
   identification.  The plastic covering the flask must be intact.
+
  a. T-flask – Must be free from visible contamination or breakage, or lack container   
-
Bottles – Check for cracks, expiration dates.
+
    identification.  The plastic covering the flask must be intact.
-
Spinners flasks – Check for cracks, expiration dates, and proper assembly.
+
  b. Bottles – Check for cracks, expiration dates.
-
Discard any biohazard or contaminated material immediately.
+
  c. Spinners flasks – Check for cracks, expiration dates, and proper assembly.
-
Never perform mouth pipetting.  Pipettor must be used.
+
 
-
When handling sterile containers with caps or lids, place the cap on its side if it  
+
* Discard any biohazard or contaminated material immediately.
-
  must be laid on the work surface.
+
 
-
Make sure not to touch the tip of the pipette to the rim of any flask or sterile
+
* Never perform mouth pipetting.  Pipettor must be used.
-
  bottle.
+
 
-
Clean the work area when finished by wiping with 70% alcohol.
+
* When handling sterile containers with caps or lids, place the cap on its side if it must be laid on the work surface.
 +
 
 +
* Make sure not to touch the tip of the pipette to the rim of any flask or sterile bottle.
 +
 
 +
* Clean the work area when finished by wiping with 70% alcohol.

Current revision

Aseptic Technique

• Protect eyes, mucous membranes, open cuts and wounds from contact with biohazard material

• Use gloves, goggles, mask, and protective clothing as necessary.

• Carry out all culturing operation in a laminar flow hood.

• Disinfect all surfaces prior to use with a disinfectant solution.

• Swab down the working surface liberally with 70% ethanol.

• Periodically spread a solution of 70% ethanol over the exterior of gloves to minimize contamination. Replace them if torn.

• In case of any spill, spread a solution of 70% alcohol and swab immediately with non-linting wipes.

• Discard gloves after use and do not wear them when entering any other lab area. Bring into the work area only those items needed for a particular procedure.

• Leave a wide clear space in the center of the hood (not just the front edge) to work on. Do not clutter the area to prevent blockage of proper air flow and to minimize turbulence.

• Swab with 70% alcohol all glassware(medium bottles, beakers, etc.)before placing them inside the hood.

• Arrange the work area to have easy access to all of it without having to reach over one item to get at another (especially over an open bottle or flask).

• Use sterile wrapped pipettes and discard them after use into a biohazard waste container.

• Check that the wrapping of the sterile pipette is not broken or damaged.

• Inspect the vessels to be used:

 a. T-flask – Must be free from visible contamination or breakage, or lack container   
    identification.  The plastic covering the flask must be intact.
 b. Bottles – Check for cracks, expiration dates.
 c. Spinners flasks – Check for cracks, expiration dates, and proper assembly.
  • Discard any biohazard or contaminated material immediately.
  • Never perform mouth pipetting. Pipettor must be used.
  • When handling sterile containers with caps or lids, place the cap on its side if it must be laid on the work surface.
  • Make sure not to touch the tip of the pipette to the rim of any flask or sterile bottle.
  • Clean the work area when finished by wiping with 70% alcohol.
Personal tools