Aseptic Technique

From OpenWetWare

(Difference between revisions)
Jump to: navigation, search
Line 11: Line 11:
• Swab down the working surface liberally with 70% ethanol.
• Swab down the working surface liberally with 70% ethanol.
-
• Periodically spread a solution of 70% ethanol over the exterior of gloves to minimize   
+
• Periodically spread a solution of 70% ethanol over the exterior of gloves to minimize  contamination.  Replace them if torn.
-
 
+
-
  contamination.  Replace them if torn.
+
• In case of any spill, spread a solution of 70% alcohol and swab immediately with non-linting
• In case of any spill, spread a solution of 70% alcohol and swab immediately with non-linting
-
 
+
wipes.
-
  wipes.
+
• Discard gloves after use and do not wear them when entering any other lab area.  Bring into the
• Discard gloves after use and do not wear them when entering any other lab area.  Bring into the
-
 
+
work area only those items needed for a particular procedure.
-
  work area only those items needed for a particular procedure.
+
• Leave a wide clear space in the center of the hood (not just the front edge) to work on.  Do not  
• Leave a wide clear space in the center of the hood (not just the front edge) to work on.  Do not  
-
 
+
clutter the area to prevent blockage of proper air flow and to minimize turbulence.
-
  clutter the area to prevent blockage of proper air flow and to minimize turbulence.
+
• Swab with 70% alcohol all glassware(medium bottles, beakers, etc.)before placing them inside the
• Swab with 70% alcohol all glassware(medium bottles, beakers, etc.)before placing them inside the
-
 
+
hood.
-
  hood.
+
• Arrange the work area to have easy access to all of it without having to reach over one item to  
• Arrange the work area to have easy access to all of it without having to reach over one item to  
-
 
+
get at another (especially over an open bottle or flask).
-
  get at another (especially over an open bottle or flask).
+
• Use sterile wrapped pipettes and discard them after use into a biohazard waste container.
• Use sterile wrapped pipettes and discard them after use into a biohazard waste container.
Line 51: Line 44:
* When handling sterile containers with caps or lids, place the cap on its side if it must be laid  
* When handling sterile containers with caps or lids, place the cap on its side if it must be laid  
-
+
on the work surface.
-
  on the work surface.
+
* Make sure not to touch the tip of the pipette to the rim of any flask or sterile bottle.
* Make sure not to touch the tip of the pipette to the rim of any flask or sterile bottle.
* Clean the work area when finished by wiping with 70% alcohol.
* Clean the work area when finished by wiping with 70% alcohol.

Revision as of 16:04, 8 September 2009

Aseptic Technique

• Protect eyes, mucous membranes, open cuts and wounds from contact with biohazard material

• Use gloves, goggles, mask, and protective clothing as necessary.

• Carry out all culturing operation in a laminar flow hood.

• Disinfect all surfaces prior to use with a disinfectant solution.

• Swab down the working surface liberally with 70% ethanol.

• Periodically spread a solution of 70% ethanol over the exterior of gloves to minimize contamination. Replace them if torn.

• In case of any spill, spread a solution of 70% alcohol and swab immediately with non-linting wipes.

• Discard gloves after use and do not wear them when entering any other lab area. Bring into the work area only those items needed for a particular procedure.

• Leave a wide clear space in the center of the hood (not just the front edge) to work on. Do not clutter the area to prevent blockage of proper air flow and to minimize turbulence.

• Swab with 70% alcohol all glassware(medium bottles, beakers, etc.)before placing them inside the hood.

• Arrange the work area to have easy access to all of it without having to reach over one item to get at another (especially over an open bottle or flask).

• Use sterile wrapped pipettes and discard them after use into a biohazard waste container.

• Check that the wrapping of the sterile pipette is not broken or damaged.

• Inspect the vessels to be used:

 a. T-flask – Must be free from visible contamination or breakage, or lack container   
    identification.  The plastic covering the flask must be intact.
 b. Bottles – Check for cracks, expiration dates.
 c. Spinners flasks – Check for cracks, expiration dates, and proper assembly.
  • Discard any biohazard or contaminated material immediately.
  • Never perform mouth pipetting. Pipettor must be used.
  • When handling sterile containers with caps or lids, place the cap on its side if it must be laid

on the work surface.

  • Make sure not to touch the tip of the pipette to the rim of any flask or sterile bottle.
  • Clean the work area when finished by wiping with 70% alcohol.
Personal tools